Ultra Main PageResearch, Training and CertificationResearchHollow axes "Welds that can not be
tested by Ultra equipment,
do not exist"
 
[wersja polska] [english version]
Hollow axes

Under construction. The article is not finished.

Missing text



System automatycznego badania osi dr±żonych - widok ogólny
Figure 1 The automatic hollow axle test - general view

Widok głowic do badawczych osi dr±żonej
Figure 2 View probes to research hollow axle

Get Flash to see this player.

Elements of instructions - descriptions

System badania osi dr±żonych w pozycji badawczej
Figure 3 The hollow axle test in a research position

Układ do badania osi dr±żonej z podstawowymi zespołami
Figure 4 Arrangement for testing hollow axle with the basic units

Schemat układu zwilżania + korek
Figure 5 Diagram of the wetting + cork

Presentation of results

Below are two presentations of results

  • presentation of the results of instantaneous during the test run and possibly the archival record
  • presentation of the results pooled so in the course of the study (part ± steaks) and (full) if the archival record

Widok ekranu podczas badań osi dr±żonych lub zapisu archiwalnego
Figure 6 View of the screen during testing hollow axle or archival record

Screen during the test is divided into four areas and illustrates the instantaneous state of research. In the upper part of the screen shows two current waveforms defectoscopic (Imaging A - two heads). Under longitudinal section axis. Oblique sections define the axis of the head of research 'in przód'i head in the "rear". In the lower right corner of the screen at the cross-section jeer indicates the instantaneous angular połażenia survey sites. Grey marked areas are areas not yet explored. Presented imaging (original) is in cylindrical coordinates.

Prezentacja ekranu zbiorcza podczas badań osi dr±żonych lub zapisu archiwalnego
Figure 7 Cumulative presentation screen during testing hollow axle or archival record

Visible detected six standard cuts on the pattern exactly in their places of location, ie the axis of the most dangerous sections.


The device consists of a shield of probes, flaw detector and bracket-adapter. Moreover, it may be equipped with a ring with the probes, as well as other research probes (e.g., welded connection). Shield of ultrasonic probes (Figure 1 and Figure 2) is used for testing, from the carrier face. Probes are placed on the target at distances resulting from the geometric analysis in a sustainable manner. The shield is designed individually for each type of axle depending on its geometrical dimensions. The shield is also arranged normal to the research probe along the axis. Also mounted device for measuring the rotation angle (inclinometer), making it possible to record the course of the study.


Wifi CUD
Figure 1 CUD BO-Fi. View from the top, visible (more about the flaw detector here):
  • "horns" (battery) power supply,
  • faceplate with power outlets and additional probes,
  • three control buttons,
  • two signaling LEDs.

Wifi CUD + tarcza
Figure 2 CUD BO-Fi. View from the bottom, visible:
  • shield of probes (6 pcs, 2MHz, Ø25mm),
  • numbers of probes and angles (e.g. 1 | 0 ° and 2 | 5,2 °),
  • centering pin.

Program
Figure 1: A screenshot of the time axis using a wireless visible flaw:
The upper-left part of the screen shows the flaw with the current indication (type A), the right side represents the recorded amplitude axis circuit, the lower are the length of the axis. Imaging involves two incisions and shown as an echo on a scale percentage of the screen for the test section as a function of the angle. In this example there are two reference notches of different depth of 0.5 mm.

individual circles on imaging (Fig. 1) are:

  • gray color indicates the outer surface of the test axis (corresponding to the amplitude of 0%, the amplitude of 100% means a means wheel)
  • color zielonm designated registration threshold set at 20% of screen height. All indications are within range marker above this threshold will be registered
  • red color indicates acceptance threshold (40% of the screen) and any of its cross. All indications above the threshold of acceptance should be considered as a potential indication of unacceptable discontinuities
  • marked in blue while the tested location on the periphery of the axis together with an indication of any indication of the amplitudes above the threshold of registration.


Pier¶cień
Rys. 3. Additional equipment, visible:
  • profiled probe with inclinometer and resistance ring,
  • probes ring with inclinometer.